Samsung The Frame Pro vs PHILIPS PUS9010 (IPS)

Samsung The Frame Pro is one of the relatively bright televisions. In synthetic tests, we managed to achieve values around 900 nits, which is quite a decent result for a lifestyle model. In full-screen scenes, such as the frame from the movie The Meg or the opening sequence in Life of Pi, the brightness maintained a level of 700–800 nits. These values allow you to fully enjoy the HDR effects and capture their cinematic magic. However, the situation complicates when smaller, point light sources appear on the screen. The edge lighting used here, equipped with the ability to local dim whole strips, does not handle them very well. It happens that small elements are overly darkened, which weakens the effect, or conversely – they become heavily brightened, but at the cost of losing black depth in that part of the image. This can be compared to light halos reminiscent of a laser beam spreading in dense fog – an effect that is visible and bright but at the same time not very natural and distracting. Fortunately, the colour aspect performs better. Thanks to the use of a quantum dot filter (QLED), the colours are saturated, and the reproduction of the DCI-P3 palette reaches over 92%. Generally, movies or series watched in HDR on The Frame Pro present a rich colour palette, even if contrast and the performance of the lighting algorithms can sometimes draw our attention away.

In the Philips PUS9010 version with an IPS panel, the HDR brightness sadly performs worse than in the previously tested 55-inch variant with a VA panel. The difference reaches about 100 nits, which is noticeably significant given the relatively low values. While the VA version could exceed 500 nits, here the maximum brightness reaches around 400 nits. This level still allows for watching movies and series in HDR, especially on streaming platforms, but the effects are clearly more subdued. Bright elements don't have the same impact, and scenes requiring high luminance are less impressive. On the plus side, the coverage of the DCI-P3 colour gamut is commendable. The IPS version offers about 91%, which is roughly 5% more than the variant with a VA panel. This translates into slightly better colour saturation in HDR content, despite the lower brightness. Colours can appear more vivid and cohesive, especially in colourful scenes.

The best results were, of course, achieved in Filmmaker mode, which immediately showed that Samsung had put effort into the factory settings. In SDR content – the most commonly viewed materials – The Frame Pro performed really well. The white balance and gamma were almost perfectly set, making the image look natural and cohesive. Yes, there were some noticeable errors, particularly in skin tones and reds, which could be overly saturated, giving everything a slightly "warmed up" character, but in everyday use, it didn't hinder the viewing experience too much. For HDR content, the situation was similar regarding the white balance. It was at a good level, however, the biggest issue turned out to be managing brightness. The EOTF curve was set in such a way that in many scenes the image appeared blown out, and the brightest areas lost detail and resulted in uniform patches of light. This severely affected realism and made colours appear very oversharpened. Fortunately, Samsung provides the option for manual adjustment of the curve in their TVs, so we opted for calibration and its results can be seen below.

We evaluated colour reproduction, as always, on factory settings, focusing on the movie mode, which in the case of Philips usually offers the best starting point. This is also a good moment to show how much the same model of TV can vary depending on the panel used. Looking at the white balance, the overall tendency remains similar to the version with the VA panel. There is still excessive red in the whites, however, in the tested unit with the IPS panel, there are also losses in the blue channel. As a result, the picture has a slightly different colour character, which is well illustrated in the comparative materials. This is a very good example showing why ready-made settings downloaded from the internet do not always work even within the same model.

However, returning to the assessment itself, this unit performs quite well, especially in SDR content. Colour tests show correct saturation and colour consistency, without glaring errors that could hinder everyday viewing. In HDR materials, it is possible to notice slight losses in reds, but these are not flaws that completely spoil the image perception. The biggest limitations do not stem directly from the colours, but rather from the whites and blacks. The use of an IPS panel and slightly lowered gamma means that the image is slightly boosted in brightness, and weak blacks further affect perceived contrast. This makes everything look brighter, but at the same time, it lacks depth, especially during evening viewing.

After calibration, the SDR mode looks almost perfect. We managed to eliminate the overly intense red saturation that previously gave the image a somewhat excessively warm character. The colours became more balanced, which translated into a natural and pleasant viewing experience for everyday content – from television to movies and series from streaming services or materials on YouTube. In HDR mode, the EOTF curve required the most work, as the factory settings caused excessive clipping of the entire image. The calibration significantly helped to "tame" this issue – the image stopped being overexposed, and details in the bright areas became more visible. Of course, the limits are set by the design of the television itself, as edge lighting reveals its limitations, and even the smallest elements of light can still appear overly bright or blend into the background. However, this is a matter of technology, not just calibration. After the correction, The Frame Pro is much more enjoyable to watch, and it is definitely worth considering if you want to make the most of the television's capabilities.

After calibration, the picture has been brought to a really reasonable level. The whole thing looks cohesive and natural, and when it comes to colour reproduction, it's hard to definitively say whether we're dealing with a VA or IPS panel. This is a good sign, showing that the television has a solid foundation for further adjustments. The larger colour gamut in this variant is a plus, as it can subtly enhance the depiction of colourful scenes, especially in HDR content. However, this advantage is largely offset by the boosted blacks resulting from the use of an IPS panel. The limited depth of black affects perceived contrast, particularly when watching in a dark room. As a result, despite noticeable improvement post-calibration, the final rating remains the same as that of the variant with a VA panel. Better colours are not able to fully compensate for the weaker blacks.

Although in 4K HDR materials the fluidity of tonal transitions in the ChooseTV Pro is not a problem at all, naturally with weaker signal quality – such as with television, HD materials, or older Full HD films – imperfections may occur. Therefore, it's crucial how the television handles these limitations thanks to the image processor. The noise reduction feature works really effectively here. At the medium setting, it eliminates unwanted bands or artifacts, smoothing the image in a visible yet not overdone way. However, it's important to remember that Samsung has a tendency to be aggressive – even at the lowest level of this feature, it can "eat" film grain. So, it's wise to use it with caution and adjust the settings according to the material being watched.

The upscaling itself is of a high standard. The ChooseTV Pro effectively boosts older materials to a native 4K resolution, maintaining good sharpness and clarity. Movies and series in lower quality simply look better here. However, it's worth mentioning a minor downside – typical for many Samsung televisions. With very old sources in poor quality, you may notice some cropping of the image edges on the left side of the screen. It's not a problem that will ruin the viewing experience, but it's good to know that it may occur.

In the Philips PUS9010, we find another iteration of the P5 Perfect Picture image processor, which aims to improve the quality of lower-grade materials. One of the components of this system is a distortion reduction function that smooths tonal transitions. It works effectively and actually reduces visible banding. Unfortunately, it does so quite aggressively. In practice, it can mute details such as material textures or film grain. This is a clear compromise, so we wouldn't particularly recommend it for movie sessions. For more casual content, like YouTube or regular television, it performs much better. The P5 processor also handles lower resolution materials quite well. The image is soft, at times even too soft, but it can easily be corrected using the sharpness slider, adjusting the effect to personal preferences. A positive aspect is also the absence of edge cropping in SD materials, which is still not standard in this class of televisions.

The fluidity of movement in The Frame Pro is not only due to the panel itself, which operates at a refresh rate of up to 144 Hz, but also the image processor and motion smoothing system. It is thanks to this that we can adjust the way movies or sports broadcasts are displayed to our own preferences. Available are sliders for blur reduction and motion judder reduction – the first function enhances the sharpness of fast movements, while the second helps to soften the effect of the "jumping" image during camera pans. Everyone can choose between a cinematic character of motion and a smoother, more "television" style.

Philips PUS9010 has a 4K panel with a refresh rate of 144 Hz, which will be appreciated mainly by sports fans and gamers. This is especially noticeable in dynamic scenes where the motion is sharp, and annoying blur is almost non-existent. When it comes to movies (standard 24 fps), Philips offers us a proven set of settings known from its higher series. Two sliders are used to control motion. “Smoothness” allows you to adjust the picture to your liking: at low settings, it maintains a cinematic character, while moving the slider to the right gives us a perfectly smooth, albeit slightly “theatrical” effect. Meanwhile, “Motion Blur Reduction” is a feature designed for sports – it ensures that fast-moving objects do not lose detail and remain clear.

Samsung The Frame Pro doesn’t pretend to be just a “living room” TV; gamers will also find something for themselves here. The manufacturer has ensured a full package of gaming features: we have support for variable refresh rate (VRR), auto low latency mode (ALLM), refresh rates up to 144 Hz, and compatibility with both G-Sync and FreeSync Premium Pro. Additionally, there’s the well-known Game Bar panel, which is a quick menu where you can check key parameters on-the-fly – from refresh rates to active image processing modes. Are there downsides? Yes, The Frame Pro doesn’t support Dolby Vision in game mode, but it’s hard to consider this a serious issue – most gamers use HDR10 anyway... so the HGIG mode. Exactly. The biggest surprise was the latest software update. Samsung... completely removed this option from The Frame PRO. In practice, this means that the TV independently interprets HDR tone mapping in games, and the user cannot enable settings designed with consoles in mind. This is a step backwards, which may disappoint more aware gamers hoping for full compliance with HGiG guidelines. We can only hope that this mistake will be quickly fixed.

An interesting feature of The Frame Pro is also the unusual placement of HDMI 2.1 ports. We have as many as five at our disposal – four are located in the One Connect module, and the fifth, in micro HDMI form, is located directly on the TV. This solution is quite unusual but very practical. Samsung clearly suggests that this is the port to connect your console or computer. Why? Because it minimises any potential delays associated with communication through the wireless One Connect, and in gaming, every millisecond counts. We have written separately about input lag, but we can reveal here that by connecting the equipment directly to the TV, we get the absolute maximum response speed from it.

Philips PUS9010 is a solid machine for gaming. It has everything that’s important: VRR, automatic game mode (ALLM), and support for HGiG. The latter is fantastic – it allows you to set HDR in games exactly the way the developers envisioned. The TV handles 120 Hz refresh rates effortlessly at every popular resolution (1080p, 1440p, and 4K). It doesn’t matter if you connect a PS5, Xbox, or a powerful PC – everything runs smoothly and just as it should. Gamers will also appreciate the Game Bar. It’s a quick, clear menu where you can immediately see if the low latency mode is active. This is especially useful when frequently switching between different consoles. The whole experience is enhanced by Ambilight. Evening sessions with this backlighting create a whole different level of atmosphere; the image seems larger, and dynamic scenes are even more impressive. Even if someone isn’t a fan of such “gimmicks,” it’s hard to deny that it makes an impression.